SPEED CHANGE GEARS AND SHAFTS (CONSTANT MESH TRANSMISSION) [01G08] 35 TRANSMISSION, DIFFERENTIAL AND CLUTCH HOUSING 450 Crawler Tractor (with 3320 or 3325 Winch) PC922 in WINCH 3320

Parts list:

№	Number	Qty	Name	Options
1	11M7087	1	Cotter Pin	4 X 40 MM
2	14H875	1	Nut	7/8", (SUB T32335, THIS APPLICATION)
2	T32335	1	LOCK NUT	7/8"
2	T36149	1	LOCK NUT	1-1/8"
3	T13179	1	SNAP RING
4	JD8929	1	Bearing Cone
5	JD8251	1	Bearing Cup
6	T13379	1	SNAP RING
7	T20802	AR	SHIM	0.05 MM (.002")
7	T20803	AR	SHIM	0.13 MM (.005")
7	T20804	AR	SHIM	0.25 MM ( 010")
8	T20800	1	SPACER
9	T31803	1	GEAR	3RD AND 4TH SPEED (31 AND 38 TEETH) (ALSO ORDER T31800) (SUB FOR T20799)
10	T31800	1	SHIFT COLLAR	(SUB FOR T23519)
11	T20794	2	GEAR	(31 TEETH)
12	T31799	3	WASHER	(SUB FOR T20793)
13	T31802	1	GEAR	7TH AND 8TH SPEED (31 AND 26 TEETH) (SUB FOR T20798)
14	T20797	1	PLATE
15	T31801	1	GEAR	5TH AND 6TH SPEED (31 AND 32 TEETH) (SUB FOR T20796)
16	T31798	1	GEAR	1ST AND 2ND SPEED (31 AND 43 TEETH) (SUB FOR T20792)
17	JD8255	1	Bearing Cup
18	JD8941	1	Bearing Cone
19	T16573	1	Pin
20	[]	1		(.466 HOLE SIZE) (IF HUB IS MARKED T18062 AT59731 MUST BE ORDERED, T18062 IS NO LONGER AVAILABLE)
20	T41190	1	HUB	(SUB FOR T31827) (.522 HOLE SIZE)
21	JD8230	1	Bearing Cup
22	JD8194	1	Bearing Cone
23	26H78	1	Shaft Key	1/4" X 3/4"
24	[]	1		(AT18523 NO LONGER AVAILABLE) ( T20785), REAR INPUT, WITH NEEDLE BEARING
25	JD8865	1	Needle Bearing
26	19H2633	3	Cap Screw	3/8" X 1-1/2"
27	24M7096	6	Washer	0.413" X 0.709" X 0.063"
28	T12789	1	LOCK PLATE
29	JD8171	1	Bearing Cone
30	JD8217	1	Bearing Cup
31	T31792	AR	SHIM	0.05 MM (.002") (SUB FOR T17199)
31	T31793	AR	SHIM	0.13 MM (.005") (SUB FOR T17200)
31	T31794	AR	SHIM	0.25 MM (.010") (SUB FOR T17201)
32	T17251	1	RETAINER	REAR IN PUT
33	T16646	1	GEAR	(18 AND 31 TEETH)
34	T31800	1	SHIFT COLLAR	(USE WHEN T31803 THIRD AND FOURTH SPEED GEAR HAS BEEN INSTALLED AS A REPLACEMENT PART) (SUB FOR T23519)
35	T19411	1	WASHER	(NOT REQUIRED WITH T32335 NUT OR T36149 NUT)
36	17H91	10	RIVET	1/2" X 2"
36	16H1592	AR	RIVET	7/16" X 1-3/4"
37	AT59731	1	PINION SHAFT	SHAFT, PINION (8 TEETH) WITH RING GEAR (MARKED T31826) (44 TEETH) (MATCHED SET) AND HUB (MARKED T41190) WITH RIVETS AND T64254 NUT, (SUB FOR AT18553) (MARKED T20791, T20775, T18062 AND AT30888)