AtlasCarParts

ALMA PRODUCTS CORE CRITERIA - CONTINUED THE SUPER HEAT SWITCH (A) IN REAR HOUSING HAS BOTH A PRESSURE SWITCH AND A TEMPERATURE BULB AND IS THE LEFT-HAND SWITCH IN THE ILLUSTRATION. IF THE SWITCH IN THE COMPRESSOR APPEARS LIKE THE RIGHT-HAND SWITCHES, 105 CORE ACCEPTANCE CRITERIA AND RETURN PROCEDURES JDM Remanufactured Components For Commerical and Consumer Equipment PC2346 in COMPONENT, REMANUFACTURED CCE


  1. Home
  2. Construction And Forestry
  3. COMPONENT, REMANUFACTURED
  4. COMPONENT, REMANUFACTURED CCE
  5. JDM Remanufactured Components For Commerical and Consumer Equipment PC2346
  6. 105 CORE ACCEPTANCE CRITERIA AND RETURN PROCEDURES
  7. ALMA PRODUCTS CORE CRITERIA - CONTINUED THE SUPER HEAT SWITCH (A) IN REAR HOUSING HAS BOTH A PRESSURE SWITCH AND A TEMPERATURE BULB AND IS THE LEFT-HAND SWITCH IN THE ILLUSTRATION. IF THE SWITCH IN THE COMPRESSOR APPEARS LIKE THE RIGHT-HAND SWITCHES,
ALMA PRODUCTS CORE CRITERIA - CONTINUED THE SUPER HEAT SWITCH (A) IN REAR HOUSING HAS BOTH A PRESSURE SWITCH AND A TEMPERATURE BULB AND IS THE LEFT-HAND SWITCH IN THE ILLUSTRATION. IF THE SWITCH IN THE COMPRESSOR APPEARS LIKE THE RIGHT-HAND SWITCHES,

Parts list:

 №  Number Qty Name Options

Next page:

105-3
ROBERT BOSCH CORE CRITERIA ALL ROBERT BOSCH RETURNED CORES MUST MEET THE GENERAL CRITERIA POINTS 1, 2, 3 AND 4 ON PAGE 105-1 IN ORDER TO RECEIVE FULL CORE CREDIT. SEE CORE ACCEPTANCE CRITERIA REDUCED CREDIT WILL BE GIVEN TO REBUILDABLE CORES WITH MIS
ROBERT BOSCH CORE CRITERIA ALL ROBERT BOSCH RETURNED CORES MUST MEET THE GENERAL CRITERIA POINTS 1, 2, 3 AND 4 ON PAGE 105-1 IN ORDER TO RECEIVE FULL CORE CREDIT. SEE CORE ACCEPTANCE CRITERIA REDUCED CREDIT WILL BE GIVEN TO REBUILDABLE CORES WITH MIS
105-3
CRITERIA FOR OTHER REMANUFACTURERS USE THE GENERAL CORE ACCEPTANCE CRITERIA ON PAGE 105-1 AT THE BEGINNING OF THIS SECTION FOR THE REMANUFACTURERS NOT MENTIONED ABOVE. [D20]
CRITERIA FOR OTHER REMANUFACTURERS USE THE GENERAL CORE ACCEPTANCE CRITERIA ON PAGE 105-1 AT THE BEGINNING OF THIS SECTION FOR THE REMANUFACTURERS NOT MENTIONED ABOVE. [D20]
105-4
CORE RETURN PROCEDURES NOTE: CORES FOR "RETURN AND REBUILD" ASSEMBLIES CANNOT BE RETURNED FOR CREDIT ONLY. THE ASSEMBLIES IN THIS CATEGORY CAN ONLY BE REMANUFACTURED AND RETURNED TO DEALERS AT A FIXED PRICE. 1. VERIFY THAT THE FAILED ASSEMBLY MEETS T
CORE RETURN PROCEDURES NOTE: CORES FOR "RETURN AND REBUILD" ASSEMBLIES CANNOT BE RETURNED FOR CREDIT ONLY. THE ASSEMBLIES IN THIS CATEGORY CAN ONLY BE REMANUFACTURED AND RETURNED TO DEALERS AT A FIXED PRICE. 1. VERIFY THAT THE FAILED ASSEMBLY MEETS T
105-4
RETURN OF CUSTOMER'S STARTER CORE FOR REMANUFACTURING THE FOLLOWING STARTERS ARE RETURNED TO THE SUPPLIER FOR REMANUFACTURING. (THE "SUB TO" OR THE "SUB FOR" PART NUMBERS ARE LISTED IN PARENTHESES.) TY1449 (TY6692) TY1465 (TY6639) TY6639 (TY1465) TY6
RETURN OF CUSTOMER'S STARTER CORE FOR REMANUFACTURING THE FOLLOWING STARTERS ARE RETURNED TO THE SUPPLIER FOR REMANUFACTURING. (THE "SUB TO" OR THE "SUB FOR" PART NUMBERS ARE LISTED IN PARENTHESES.) TY1449 (TY6692) TY1465 (TY6639) TY6639 (TY1465) TY6
105-5
DEPOT CORE RETURN ADDRESSES DEPOTS SHOULD RETURN CORES TO THE ADDRESSES LISTED BELOW. SHIPA CODES SHOWN NEXT TO SUPPLIER ARE CORE RETURN ADDRESS CODES. SHIPA CODES ARE PROVIDED ON FOLLOWING PAGES FOR EACH REMAN COMPONENT. THE ATTENTION LINE ON THE AD
DEPOT CORE RETURN ADDRESSES DEPOTS SHOULD RETURN CORES TO THE ADDRESSES LISTED BELOW. SHIPA CODES SHOWN NEXT TO SUPPLIER ARE CORE RETURN ADDRESS CODES. SHIPA CODES ARE PROVIDED ON FOLLOWING PAGES FOR EACH REMAN COMPONENT. THE ATTENTION LINE ON THE AD
105-2
ALMA PRODUCTS AC COMPRESSORS NOTE: OIL THAT LEAKS FROM THE SKIP AREA OF WELD AT THE FRONT FLANGE AND MAIN HOUSING IS USUALLY OIL USED IN COMPRESSOR ASSEMBLY. USE A LEAK DETECTOR TO VERIFY FREON LEAKAGE. FULL CREDIT IS GIVEN FOR UNITS WHICH HAVE A [D1
ALMA PRODUCTS AC COMPRESSORS NOTE: OIL THAT LEAKS FROM THE SKIP AREA OF WELD AT THE FRONT FLANGE AND MAIN HOUSING IS USUALLY OIL USED IN COMPRESSOR ASSEMBLY. USE A LEAK DETECTOR TO VERIFY FREON LEAKAGE. FULL CREDIT IS GIVEN FOR UNITS WHICH HAVE A [D1
105-1
CORE ACCEPTANCE CRITERIA IF THE RETURNED CORE HAS ONE OR MORE OF THE FOLLOWING CONDITIONS, ZERO CORE CREDIT WILL APPLY. CORES WITHOUT ANY OF THE FOLLOWING CONDITIONS WILL RECEIVE 100 PERCENT CORE CREDIT. 1. THE ASSEMBLY MUST BE COMPLETE AND INTACT. [
CORE ACCEPTANCE CRITERIA IF THE RETURNED CORE HAS ONE OR MORE OF THE FOLLOWING CONDITIONS, ZERO CORE CREDIT WILL APPLY. CORES WITHOUT ANY OF THE FOLLOWING CONDITIONS WILL RECEIVE 100 PERCENT CORE CREDIT. 1. THE ASSEMBLY MUST BE COMPLETE AND INTACT. [
105-1
CORE IDENTIFICATION, COMPONENT WHERE USED AND RETURN PROCEDURES TO IDENTIFY A REMANUFACTURED COMPONENT PART NUMBER, LOOK AT THE COMPONENTS LISTED IN THE SECTION FOR THE COMPONENT. A LISTING OF MACHINES THAT USE THE COMPONENT FOLLOWS THE COMPONENT [D1
CORE IDENTIFICATION, COMPONENT WHERE USED AND RETURN PROCEDURES TO IDENTIFY A REMANUFACTURED COMPONENT PART NUMBER, LOOK AT THE COMPONENTS LISTED IN THE SECTION FOR THE COMPONENT. A LISTING OF MACHINES THAT USE THE COMPONENT FOLLOWS THE COMPONENT [D1